ANS-810 / ANS-510 (PROPER RNS-510 alternative)

[bazzle]

Since updating to M140 I have had a couple of canbus issues. I realised the steering wheel buttons were not working anymore. I went into the hidden menu and changed the can bus module from can-s to can-v. Now I have working volume and mute buttons but the right hand set isnt recognised. ie. input select / track change.
Any one had the same?

Baz

[HiSteveLoveTheShow]

I have a ANS-620 navi HU in fitted my 2008 pre-facelift Skoda Octavia VRS CR170 a good while back and later a Maxidot retrofitted, too.

When going from the MFD to the Audio menu, the Maxidot completely locks itself to said menu, and cannot be changed without either fuse removal, or battery disconnection. I'm pretty sure this isn't normal, and no amount/combination of button presses unlocks it.

Hmm, whilst skimming this thread, which seems to have a lot of information about these units, and there seems to be a hidden menu with various CANBUS options.

Listed are: CAN-S, CAN-V, CAN-X and CAN-M (which is the current selected option).

With previous VCDS scans, I've always had the following CAN gateway error listed (since the HU was fitted). Could this be due to the wrong CAN setting in the HU? Errors are gone with the OEM HU installed.

Address 19: CAN Gateway Labels: 1K0-907-530-V3.clb
Part No SW: 1K0 907 530 Q HW: 1K0 907 951
Component: J533__Gateway H16 0202
Revision: H16 Serial number: 2700K087020CCB
Coding: E9807F060002021303
Shop #: WSC 11679 000 1048576
VCID: 3561C75F5CB4ADB6775-8060

2 Faults Found:
01305 - Databus for Infotainment
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 1
Fault Frequency: 116
Reset counter: 110
Mileage: 94426 km
Time Indication: 0
Date: 2000.00.00
Time: 20:50:09

01304 - Radio
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 2
Fault Frequency: 14
Reset counter: 150
Mileage: 94426 km
Time Indication: 0
Date: 2000.00.00
Time: 20:52:02

Or could it be an issue with the firmware? This is what I get when I touch the screen on the mid-far left in the AUX IN menu:

Version

BSP: ANS510AS.611
MPU: ANS510AS.M93
Servo: 8B37.DL30.1200W.100414
MCU: ANS510AS.121123.m1.T1
BT: 20120512
MST701: 6.2.07
Region code 9


Cheers.

[bazzle]

Easy way to tell if it the canbus code is to see if the steering wheel buttons work. If they did, and now dont ...

[HiSteveLoveTheShow]

I don't have steering wheel buttons - do you mean the stalk controls?

[bazzle]

No
Some steering wheels have the volume controls duplicated there etc. If they stop working the can bus is not getting there.
Also some head units get that or similar code as they dont get recognised as an VW unit thru the canbus. If it works leave it alone

[wai]

I hope this is the right area, but I have a question on iGo Primo on these units.

When you enter an address to find, it comes back with a route, and then depending on the route, you will see a number in brackets on the Go button.

I assume that if it is say "Go (6)", it would mean that there are 6 alternative routes. That being the case, how do you bring up those alternative routes and pick from them?

Thanks.

[HiSteveLoveTheShow]

I hope this is the right area, but I have a question on iGo Primo on these units.

When you enter an address to find, it comes back with a route, and then depending on the route, you will see a number in brackets on the Go button.

I assume that if it is say "Go (6)", it would mean that there are 6 alternative routes. That being the case, how do you bring up those alternative routes and pick from them?

Thanks.

I thought it was some kind of countdown timer? What happens if you press it?

[HiSteveLoveTheShow]

Also, is it possible to retrofit TMC to these units?

[wai]

I thought it was some kind of countdown timer? What happens if you press it?

I do not believe it is a countdown timer as the number varies depending on the destination. As for pressing it, you have to to get the navigation to start.

[bazzle]

Generally it is the time until it starts navigating. Allowing you to cancel if you want. Pressing it should start the route calculation.


All you need is here. Including latest programs, maps, Camera poi's etc.

Fixmygps Mk III - GPS Navigation Made Easy - Help with IGO 8, 8.3 & Primo Software
Im a Mod on that site.

Bazzle