Juzz's new VR6

**Juzzpc** · 12-05-2015, 11:08 AM

Originally Posted by UKDavo

Is yours the OBD2? Or did you remove the arches?

I've been contemplating a respray or wrap but need to look into it abit more.

Obd2

**Juzzpc** · 13-05-2015, 10:03 AM

back to vr tail lights, thinking about shaving the rear badge and wiper,

**UKDavo** · 13-05-2015, 11:02 AM

I've blacked my badge. Don't fancy bogging the hole :/.

I want to remove the wiper, just need to find a suitable bung. I've seen a cool Wolfsburg bung which looks sweet!

**Juzzpc** · 13-05-2015, 11:55 AM

Originally Posted by UKDavo

I've blacked my badge. Don't fancy bogging the hole :/.

I want to remove the wiper, just need to find a suitable bung. I've seen a cool Wolfsburg bung which looks sweet!

nah i don't want to bog it, i want to weld a plate in the recess. i want to keep bog to a minimum.

**beausuf** · 13-05-2015, 05:51 PM

Pretty sweet little car man, I just read through nearly every page. Looks heaps neater since you've bought it.

How are you finding the coilovers? I've been tossing up between the ones that you have and JOM. Both I can only assume are stiff as hell and you get what you pay for. Also do you struggle getting a jack under the dam thing? haha. I just did some playing around on my mk3 today and am wondering how the hell I will get a jack under it once it's lowered.

**Juzzpc** · 13-05-2015, 06:05 PM

Originally Posted by beausuf

Pretty sweet little car man, I just read through nearly every page. Looks heaps neater since you've bought it.

How are you finding the coilovers? I've been tossing up between the ones that you have and JOM. Both I can only assume are stiff as hell and you get what you pay for. Also do you struggle getting a jack under the dam thing? haha. I just did some playing around on my mk3 today and am wondering how the hell I will get a jack under it once it's lowered.

thanks man! yeah the coilovers are pretty stiff but eh they are only cheapies.
yeah i now have to drive onto blocks off wood to fit the jack under it, + sometimes i need to take off my lip, i need a low profile jack which are for lowered cars.

**BurgundyMk3** · 13-05-2015, 07:01 PM

Go to bunnings and there is a set of 4 plastic 21mm plugs in a packet for like 4 bucks. I used the original seal the wiper uses and it's been sweet. I have been meaning to take thenpkug out and chuck some plummers thread tape around it as an extra step during winter but it hasn't leaked so far.

**Juzzpc** · 13-05-2015, 11:51 PM

Originally Posted by BurgundyMk3

Go to bunnings and there is a set of 4 plastic 21mm plugs in a packet for like 4 bucks. I used the original seal the wiper uses and it's been sweet. I have been meaning to take thenpkug out and chuck some plummers thread tape around it as an extra step during winter but it hasn't leaked so far.

I don't want to bung it, I wanna be smoooooth

**Juzzpc** · 13-06-2015, 04:27 PM

tried to align my bumper up today as it's been off place and the tyre is close to he corner of the bumper, I want to run spacers on the back to make it abit more flush and looking abit beefier, but it'll scrap on that part of the bumper.

decided to see what was wrong, looks as if these sliding tabs were broken, so I tried to plastic weld them, (I used the same plastic as the bumper too) but didn't bond well enough and in the struggle to put the bumper back on it snapped off again, didn't have enough time so I just left it,

also, what are these vent things?